d'occasionDisponible
Catégorie du produit : Backpressure Valves & Flow Control
Backpressure Valves & Flow Control
Steady, repeatable flow depends on holding the right pressure downstream, and that is the job of backpressure valves and flow control devices. In chromatography, dosing and process lines they keep a constant load on the pump so flow stays smooth and detectors read cleanly. Buyers here look at pressure rating, wetted materials and port sizes to match a valve to their fluid and line pressure. Listings set out the setpoint range and connection type so you can specify the part with confidence. Reach the seller directly to confirm chemical compatibility.
Afficher les filtres
Trier par
Les plus pertinents
d'occasionDisponible
Catégorie du produit : Backpressure Valves & Flow Control
Broadley James Corporation Flow Controller S/601 Flow Controller
d'occasionVendu récemment
Catégorie du produit : Backpressure Valves & Flow Control
AVK Flanged gate valves
d'occasionDisponible
Catégorie du produit : Backpressure Valves & Flow Control
Buracco Steam valves
4
Annonces en ligne
2
Marques de confiance
100 %
Vendeurs vérifiés
24/7
Place de marché mondiale
Backpressure and Flow Control Device Types
Within the liquid handling, pumps and fluid control category, backpressure valves and flow control hardware ranges from fixed cartridges to adjustable regulators and metering valves. The variants differ in how they set pressure and whether the point is fixed or tunable.
Adjustable backpressure regulators
Spring or dome loaded units that let you dial in the downstream pressure to suit the method. They hold the pump under a steady load so flow stays pulse free through a detector.
Fixed cartridge restrictors
Sealed inline parts that impose a set backpressure without any adjustment. They are simple and repeatable for a known method where the pressure never needs to change.
Metering and needle valves
Fine thread valves that trim flow by hand for precise manual control on a line. They suit split flows and bleed lines where small adjustments matter.
Check and relief valves
Directional and pressure limiting valves that protect the line from backflow and overpressure. They safeguard pumps and columns when a blockage builds.
Dernières annonces : Backpressure Valves & Flow Control
Pourquoi choisir Machinery Masters
Uniquement des vendeurs vérifiés
Chaque vendeur est vérifié avant la mise en ligne de la moindre annonce. Machinery Masters contrôle également l'exactitude des annonces, afin que les acheteurs puissent investir en toute confiance dans des machines de grande valeur.
Portée mondiale
Les annonces proviennent de vendeurs de toute l'Europe, d'Amérique du Nord et d'ailleurs. Cette portée élargit le choix au-delà de tout réseau régional de revendeurs, et c'est souvent le seul moyen de trouver des modèles qui ne sont plus fabriqués en bon état.
Options de financement flexibles
Les annonces éligibles bénéficient d'un financement par l'intermédiaire de partenaires. Les conditions sont affichées directement sur les pages produit concernées, ce qui permet d'étaler le coût au lieu d'épuiser votre fonds de roulement en une seule fois.
Contact direct avec le vendeur
Aucun intermédiaire entre l'acheteur et le vendeur. Renseignez-vous sur l'historique d'entretien, organisez des inspections et négociez directement avec la personne qui connaît réellement la machine.
Applications and Uses
Backpressure and flow control devices appear wherever flow must stay constant and pressure must stay bounded. These are the common settings.
Liquid chromatography lines
Holding a steady backpressure so the pump delivers pulse free flow to the column and detector. Stable pressure keeps retention times and peak shapes reproducible.
Supercritical and high pressure systems
Maintaining the pressure needed to keep a fluid in its working phase during extraction or reaction. A dome loaded regulator holds the setpoint against changing flow.
Reagent dosing circuits
Trimming and stabilising flow on dosing lines so delivered volumes stay accurate. Metering valves let an operator fine tune the rate by hand.
Pump and column protection
Limiting overpressure and preventing backflow when a line partially blocks. Relief and check valves shield expensive columns and pump heads.
Benefits from Machinery Masters
The marketplace makes it straightforward to source the small but critical valves and regulators that keep a fluid line stable.
01
Flow control parts beside the pumps they serve
These valves and regulators sit in the same category as the pumps and lines they support, so you specify the whole circuit in one place.
02
Sensible pricing on serviceable valves
Many valves are simple mechanical parts a seller can offer well below new after inspection, which keeps the cost of a spare or upgrade low.
03
Fit confirmed before you order
You put the fluid, pressure and fitting details to the seller and get a straight answer, so you never order a used valve that will not seal on your line.
Frequently Asked Questions sur Backpressure Valves & Flow Control
Choose a valve whose setpoint range brackets the pressure your method needs, with the working point away from either extreme. A regulator set near the top of its range holds less steadily than one working mid scale. Note both your normal operating pressure and any peaks during flow changes. Give the seller those figures and they can confirm the unit covers your window.
The valve seat, body and seals must resist your solvents and any acids or salts in the fluid. Stainless steel bodies suit many aqueous and organic methods, while more aggressive chemistry may call for a polymer or coated wetted path. Ask the seller to confirm the seat and seal materials on the specific unit. Matching these avoids swelling, corrosion and leaks in service.
A fixed cartridge is simplest when your method always runs at one pressure and you value repeatability over flexibility. An adjustable regulator earns its place when you change flow rates or run several methods on the same line. Consider how often the setpoint needs to move. The seller can advise which style the listed part is and how finely it adjusts.
A stable backpressure smooths pump pulsation, which is a common source of baseline noise and drift in chromatography. Fitting a regulator sized to your flow steadies the delivery reaching the detector. It will not fix noise from other sources such as bubbles or a failing lamp, so diagnose the cause first. The seller can describe how a given unit performed on their system.
Sellers on the marketplace are verified, and a valve listing should state whether the part was pressure tested or inspected before sale. You can ask directly for that detail and request evidence of a leak check. Because you deal with the seller with no middleman in between, the exchange is quick and specific. Agree on any inspection you want before purchase.
Catégories associées
Tout Manipulation de liquides, pompes et contrôle des fluidesSystèmes de pipetage automatisésPompes centrifugesPompes à membranePompes doseusesStations de manipulation de liquidesPompes péristaltiquesUnités pneumatiquesTêtes de pompe et accessoiresPompes à palettesPousse-seringues et perfuseursPompes et systèmes à vide